Get HP HP BladeSystem c7000 Enclosure HP BladeSystem Onboard Administrator User Guide. Get all HP manuals! Sign up to create an account Facebook Twitter. By clicking Create Account, you agree to the Company’s.
Advertising
Configuring the HP BladeSystem c7000 enclosure and enclosure devices 120
- QuickSpecs HPE BladeSystem c7000 Enclosure. Page 3. Provides a wizard-based initial setup process for easy configuration. A BladeSystem c7000 enclosure provides the following benefits:. With local and remote hardware management integrated across the solution, one full enclosure can be managed as easily as one server.
- HP BladeSystem c7000 Enclosure hardware installation Installing Onboard Administrator modules The HP BladeSystem c7000 Enclosure is shipped with one HP BladeSystem Onboard Administrator module installed and can support up to two Onboard Administrator modules.
- HPE BladeSystem c-Class Enclosure Troubleshooting Guide Abstract This document is for the person who installs, administers, and troubleshoots HPE BladeSystem c-Class products. Only persons experienced in server blade technology and configuration should attempt these procedures. Hewlett Packard Enterprise assumes you are qualified in the.
- 3 Removal and replacement procedures NOTE: The HP BladeSystem c7000 Carrier-Grade Enclosure is similar to the HP BladeSystem c7000. Refer to the HP BladeSystem c7000 Enclosure Maintenance and Service Guide for the following removal and replacement procedures: Server blades Device bay shelves and shelf blanks.
Field
Possible value
Description
System Location
0 to 20 characters including all
printable characters and the
space
The SNMP location of the enclosure typically
used to identify the physical or topographical
location of the Onboard Administrator. Zbrush manual pdf.
System Contact
0 to 20 characters including all
printable characters and the
printable characters and the
space
The name of the system contact, used to identify
an individual or group of individuals who are to
an individual or group of individuals who are to
be contacted in the event of any status change
in the HP BladeSystem Onboard Administrator.
Read Community
0 to 20 characters including all
printable characters and the
space
The Read Community string enables the client to
read information but not to manipulate the alerts
or status of the HP BladeSystem Onboard
Administrator through SNMPv1 or SNMPv2.
The default community name is 'public' and
The default community name is 'public' and
will allow a user to receive notification traps
and alerts, but not to change or manipulate the
status.
status.
Write Community
0 to 20 characters including all
printable characters and the
space
space
The Write Community string enables the client
to manipulate alerts of HP BladeSystem
Onboard Administrator status through SNMPv1
Onboard Administrator status through SNMPv1
or SNMPv2. You can remotely clear alerts and
mark them as 'viewed' or otherwise through
their SNMP management client through the
SNMP agents.
SNMP agents.
Hp Bladesystem C7000 Enclosure Manual
Engine ID String
1 to 27 printable characters,
final Engine ID will be a
hexadecimal string that begins
hexadecimal string that begins
with '0x' and is derived from
this string
The Engine ID String is used to create the engine
ID hex value.
The engine ID is combined with the user name to
The engine ID is combined with the user name to
create a SNMPv3 user for each enclosure.
When the engine ID is unique to an enclosure,
users with the same name on different
enclosures are unique.
enclosures are unique.
The Engine ID string defaults to the serial
number of the enclosure.
After editing any field in this subcategory, to save the changes, click Apply.
Adding SNMP alert destinations
To remove a current SNMP alert destination, select the check box, and click Delete.
To add a new SNMP alert destination, click New. The Add SNMP Alert screen appears.
To send a test SNMP trap to all of the configured trap destinations, click Send Test Alert. You must enable
Adding SNMP alert destinations
To remove a current SNMP alert destination, select the check box, and click Delete.
To add a new SNMP alert destination, click New. The Add SNMP Alert screen appears.
To send a test SNMP trap to all of the configured trap destinations, click Send Test Alert. You must enable
SNMP to use this function.
Advertising
Hp Bladesystem C7000 Enclosure Manual Download
Popular Brands
Popular manuals